風管加工過程中出現問題怎么避免？

發布人：http://www.bnlfans.net   發布時間：2023-04-24 16:08:27

我們在許多住宅建筑和辦公建筑中都可以看到通風管道的身影，但大家不知道的是濟南通風管道在加工的時候是會產生很多問題的，這些問題令很多工作人員都很苦惱，下面我們來了解一下風管加工時經常會出現的問題及解決措施，在風管加工過程中，可能會出現以下問題：

We can see the presence of ventilation ducts in many residential and office buildings, but what everyone is not aware of is that there are many problems that can arise during the processing of ventilation ducts in Jinan. These problems make many workers very distressed. Below, we will learn about the common problems and solutions that occur during the processing of air ducts. During the processing of air ducts, the following problems may occur:

尺寸不準確：由于加工設備或操作不當，風管的尺寸可能會偏差較大，導致無法與其他部件配合或者影響風管的性能。

Inaccurate size: Due to improper processing equipment or operation, the size of the air duct may deviate significantly, resulting in inability to fit with other components or affecting the performance of the air duct.

焊接質量不佳：如果風管的焊接不牢固或者存在裂縫、氣泡等問題，就會影響風管的密封性和耐用性，甚可能引發事故。

Poor welding quality: If the welding of the air duct is not firm or there are cracks, bubbles, and other issues, it will affect the sealing and durability of the air duct, and may even cause safety accidents.

材料選擇不當：如果選擇的材料不符合要求，或者使用的材料質量不穩定，就會影響風管的耐用性和性能。

Improper material selection: If the selected material does not meet the requirements or the quality of the material used is unstable, it will affect the durability and performance of the air duct.

端口位置不對：如果風管的端口位置不正確，就會導致風管連接時無法對接或者影響風管的氣流性能。

Incorrect port position: If the port position of the air duct is incorrect, it will cause the air duct to be unable to connect or affect the airflow performance of the air duct.

污染：在加工過程中，如果沒有正確處理材料或工作環境，就可能會導致風管表面污染，影響風管的衛生性和美觀性。

Pollution: If materials or working environment are not properly handled during the processing, it may cause surface pollution of the air duct, affecting its hygiene and aesthetics.

風管翹角及彎頭角度不準：折角不平直;矩形風管兩相對平面、兩端面不平行;咬口不嚴;對角線不相等。會使風管連接受力不均勻，安裝后的風管不平直，法蘭盤墊片不嚴密，系統漏風，造成空調負荷損失，并且縮短使用壽命。

Incorrect angle of air duct warping and bending: uneven bending angle; The two opposite planes and two end faces of a rectangular air duct are not parallel; Not biting tightly; Diagonal lines are not equal. It will cause uneven stress on the air duct connection, uneven installation of the air duct, loose flange gasket, system air leakage, resulting in air conditioning load loss and shortened service life.

展開下料時，應對板料嚴格角方，對每片板料的長度、寬度以及檢驗對角線，使它們的偏差控制在允許范圍內;下料后的板料，應將風管相對面的兩片板料重合檢驗尺寸準確性。

When unfolding the cutting process, the corners of the sheet should be strictly square, and the length, width, and inspection diagonal of each sheet should be controlled within the allowable range of deviation; After cutting, the size accuracy of the two sheets on the opposite side of the air duct should be checked by overlapping them.

風管加工材料未達標：風管平面下沉，側面向外凸起，有明顯的變形;板材表面不平整，厚度不均勻，有明顯的壓痕、裂紋、砂眼、結疤和銹蝕等情況。運轉時風管漏風，空調負荷增加，同時風壽命和性能被影響。

The processing materials of the air duct are not up to standard: the plane of the air duct sinks, the side protrudes outward, and there is obvious deformation; The surface of the board is uneven, with uneven thickness, obvious indentation, cracks, sand holes, scarring, and rust. During operation, the air duct leaks, increasing the air conditioning load, and affecting the air service life and performance.

在使用風管加工設備制作風管前，要先檢查材料出廠合格證書和材料質量證明還有外觀厚度等，保證材料是可用的。

Before using air duct processing equipment to produce air ducts, it is necessary to check the material factory certificate, material quality certificate, and appearance thickness to ensure that the materials are usable.

為了避免上述問題，需要在風管加工前進行充分的準備工作，包括選擇合適的材料和設備、確保操作規范和、對加工過程進行嚴格的質量控制等。此外，還需要對加工過程中出現的問題進行及時的處理和糾正，以確保風管加工的質量和效果。更多相關的內容就來我們網站http://www.bnlfans.net咨詢！

To avoid the above issues, it is necessary to conduct sufficient preparation work before processing the air duct, including selecting suitable materials and equipment, ensuring operational norms and safety, and implementing strict quality control during the processing process. In addition, it is necessary to promptly handle and correct the problems that occur during the processing process to ensure the quality and effectiveness of the air duct processing. For more relevant content, come to our website http://www.bnlfans.net consulting service