工業空調的風管加工有哪些規范和注意事項?

發布人：http://www.bnlfans.net   發布時間：2022-05-06 16:33:16

在車間通風降溫工程中，空調通風管道的加工安裝是一個非常重要的環節。通風管道的加工和安裝方法有一些具體的，才能與空調連接，發揮其作用，完成其使用效果。

1： Specifications. The specifications mentioned here are the basic specifications of the ventilation duct, as well as the size and size of the ventilation duct we need. It is worth noting that when we determine the specifications, we need to be associated with the use of air conditioning. Only in this way can we ensure that after setting the specifications of the ventilation duct, it can be connected with the air conditioner, play its role and complete its use effect.

二：類型。通風管的種類很多。不同類型的空調與管道配合使用，效果不同，尤其是通風管道的隔熱。因此，如果我們要加工通風管道以更好地與空調配合使用，我們還需要在加工前考慮其類型，這是確保它們高工作并發揮有利作用的良好條件。

2： Type. There are many kinds of ventilation pipes. Different types of air conditioners have different effects when used together with pipes, especially the heat insulation of ventilation pipes. Therefore, if we want to process ventilation ducts to better cooperate with air conditioners, we also need to consider their types before processing, which is a good condition to ensure their high work and play a favorable role.

總之，在加工通風管之前，一定要結合空調的基本情況，注意通風管的規格和類型。不同的空調需要不同的通風管、不同的規格、不同的類型。因此，當涉及到通風管道時，需要考慮上述問題。

In short, before processing the ventilation pipe, we must pay attention to the specification and type of the ventilation pipe in combination with the basic situation of the air conditioner. Different air conditioners need different ventilation pipes, different specifications and different types. Therefore, when it comes to ventilation ducts, the above problems need to be considered.

通風管道加工規范：

Ventilation duct processing specification:

1、風管加工時，為保證風管生產后的強度，切割時應預留20mm鋁箔作為保護邊;

1. During air duct processing, 20mm aluminum foil shall be reserved as protective edge during cutting to ensure the strength of air duct after production;

2、風管在拼接前需要預先組裝好，檢查接縫是否嚴密，尺寸是否符合要求。根據季節溫度、濕度和粘合劑特性確定粘合時間。加入后，用正方形檢查。鋼帶。垂直度和對角線偏差的調整需要符合規定。

2. The air duct needs to be pre assembled before splicing to check whether the joint is tight and whether the size meets the requirements. The bonding time is determined according to the seasonal temperature, humidity and adhesive characteristics. After adding, check with a square. Steel belt. The adjustment of perpendicularity and diagonal deviation shall meet the requirements.

3、通風管道加工時，請做好現場預制板、管道成品的保護工作。

3. During the processing of ventilation pipes, please protect the prefabricated plates and finished pipes on site.

4、連接安裝后，應檢查接頭接頭，接頭后應平整、彎曲。錯位局部裂紋、大于2mm的縫隙等缺陷。

4. After connection and installation, check the joint, which shall be flat and bent. Dislocation, local crack, gap larger than 2mm and other defects.

5、風管支架與吊架的距離符合標準。

5. The distance between air duct support and hanger meets the standard.

以上就是為大家介紹的有關濟南鐵皮風管加工http://www.bnlfans.net的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務

The above is about the processing of Jinan iron sheet air duct http://www.bnlfans.net I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service