鐵皮通風管道安裝要注意哪些質量控制？

發布人：http://www.bnlfans.net   發布時間：2021-11-15 11:05:56

來講，就白鐵皮通風管道在進行安裝的時候，先要注意的其實也就是通風管道上的組裝，在風管比較短的時候，在很大的程度上其實也就是能一次在地面進行組裝而成，緊接著，就風管比較長的時候，在很大的程度上其實也就是能直接的就視安裝場地的情況，直接的就在地面進行分段組裝。

First of all, when installing the white iron sheet ventilation duct, the first thing to pay attention to is the assembly on the ventilation duct. When the air duct is relatively short, it can be assembled on the ground to a great extent. Then, when the air duct is relatively long, it can directly depend on the situation of the installation site to a great extent, It is directly assembled in sections on the ground.

就濟南白鐵皮通風管道在進行組裝的時候，應該是要盡量調整一下其風道的度與水平度，就其在很大的程度上其實也就是能直接的就避免了風管扭曲或者是上下起波，左右擺動，且就每段風道上其實也也就是要注意不可以超過10m。在進行組裝的時候，墊片也應該要注意墊平，對于其法蘭螺栓也應該是要均勻的進行擰緊，就螺母帽均會朝向同一方向。

When assembling the Jinan white iron sheet ventilation duct, it should try to adjust the centrality and levelness of the air duct as much as possible. To a great extent, it can directly avoid the air duct distortion or wave up and down, swing left and right, and in fact, it should not exceed 10m in each section of the air duct. During assembly, the gasket should also be leveled. The flange bolts should also be tightened evenly, and the nut caps will face the same direction.

再者，關于白鐵皮通風管道上的就位，就風管在進行就位之前，在很大的程度上其實也就是應該要注意直接的就檢查一下其全部支架上的水乎度與標高，緊接著，也就是要注意應該是要直接的就檢查一下其支架的牢固程度，對于其風管就位其實也就是能采用直接與吊具這兩種方法。

In addition, for the positioning of the white iron sheet ventilation duct, before the air duct is positioned, it should be paid attention to directly check the water level and elevation of all its supports. Then, it should be paid attention to directly check the firmness of its supports, In fact, the two methods of direct and spreader can be adopted for the positioning of the air duct.

緊接著，對于濟南白鐵皮通風管道上的風管斷面上比較小，又其位置上比較低的話，在很大的程度上其實也就是可以直接的就可以采用人工就位方法，只需要直接的就搭設簡易腳手架也就可以了。就白鐵皮通風管道上的風管斷面比較大并且就其管段上比較長的時候，就其在很大的程度上其實也就是能直接的就采用滑輪、倒鏈或者是大繩等方法進行吊裝。為了方便通風管道上的風道進行就位，一般情況下也就是要注意應該是直接把風道吊在了腳手架上面。

Then, if the section of the air duct on the Jinan white iron sheet ventilation duct is relatively small and its position is relatively low, to a large extent, the manual positioning method can be directly adopted, and it only needs to directly set up a simple scaffold. When the section of the air duct on the white iron sheet ventilation duct is relatively large and the pipe section is relatively long, it can be hoisted directly by pulley, chain block or large rope to a great extent. In order to facilitate the positioning of the air duct on the ventilation duct, it should be noted that the air duct should be directly hung on the scaffold.