白鐵皮人工的加工要求標準您清楚嗎？

發布人：http://www.bnlfans.net   發布時間：2017-10-26 17:03:28

1.使用白鐵加工壓口機時不要用力推動鐵皮。壓橫接號應先將咬口部分鏟掉。手離壓輪要大于20毫米。

1. the use of tin processing pressure machine don't push iron. The horizontal connection number should be first removed from the bite part. Hand off pressure roller is greater than 20 mm.

使用咬口機要將白鐵皮的咬口處對好后再開車。開車時工件要扶穩，手指不得放在咬口機軌道上。

Use the bite holder to bite the iron sheet properly and then drive it again. When driving, the workpiece should be stable, and the finger should not be placed on the rail of the bite machine.

2.滾床的齒輪必須加防護套罩。使用時應離開兩壓輥的縫隙，并宜在進料處加擋板。

2. gear hobbing machine must be combined with a protective cover. When using, the gap between the two rollers should be left, and the safety baffle should be added at the feeding place.

使用白鐵加工剪板機，上刀架不得放置工具等物品。調整鐵皮時腳不能放在踏板上。剪切時禁止把手伸入壓板空隙中。

The use of tin processing shears, tools and other items shall not be placed on the knife. The feet should not be placed on the pedals when adjusting the iron sheet. When cutting, don't put the handle into the gap of the press plate.

3.進行錫焊時要戴手套，不許仰焊。熔錫時錫液不許著水，防止飛濺。使用的電烙鐵及鹽酸要妥善保管。

To wear gloves 3. soldering, no overhead welding. Tin bath is not allowed to splash water and prevent spatter. Proper use of electric iron and hydrochloric acid should be kept in good order.

4.操作電鉆和半自動螺絲刀時，要垂直于白鐵加工的鐵皮，旦不要用力過猛。使用點焊機要檢查有無漏電漏水現象，操作時要戴焊工手套、鞋蓋、墨鏡等防護用品，冬季使用后要放盡冷卻液。

4. the operation of electric drill and semi-automatic screwdriver, perpendicular to the processing of tin tin, Dan do not overexert. Use spot welding machine to check whether there is leakage or leakage, and wear protective gloves such as welder gloves, shoes cover, sunglasses and so on. The cooling liquid should be put out after use in winter.

5.在保溫層外包白鐵皮時，要扎好衣袖、褲腳、袖口，戴好口罩、防塵帽和防護眼鏡。

5. in the insulation layer outsourcing tin, to tie the sleeves, trousers, cuffs, wearing masks, protective glasses and dust cap.

6.吊運風管及材料時，索具要拴牢，并應加溜繩穩住。用麻繩滑車吊運時拉繩人要戴帽。

6. lifting air pipes and materials, rigging should be fastened ropes, and should be added. With a rope pulley hanging rope to wear a helmet.

7.不要在未固定的風管、架空的鐵皮上站立和行走。

7. do not stand and walk on the unfixed air pipe and the aerial iron sheet.

8.廢棄的邊角余料要及時清理，防止刺傷手腳。

8. waste leftover materials should be cleaned in time to prevent stab wounds.