通風管道講解按用途區分有哪些？

發布人：http://www.bnlfans.net   發布時間：2023-09-03 14:19:08

結合實際情況進行檢查復核，再按編號進行排列，風管系統的各部分尺寸和角度確確無誤后，即開始風管組對工作。風管各管段之間的連接采用法蘭連接，接口處要求嚴密不漏風。一次吊裝風管的長度要根據建筑物的條件，風管的壁厚，吊裝方法和吊裝機具配備情況確定，組對好的風管可把兩端的法蘭做為基準點，以中間法蘭為測點，拉線測量風管的連接是否平直，偏差大時要進行調整

Based on the actual situation, conduct inspection and review, and then arrange according to the number. Once the dimensions and angles of each part of the air duct system are confirmed to be correct, the air duct assembly work begins. The connection between each section of the air duct adopts flange connection, and the interface must be tight and air tight. The length of the air duct to be lifted at a time should be determined based on the conditions of the building, the wall thickness of the air duct, the lifting method, and the allocation of lifting equipment. The assembled air duct can use the flanges at both ends as reference points, and the middle flange as the measuring point. Pull a line to measure whether the connection of the air duct is straight, and adjust it when there is a large deviation

薄鋼板通風管道制造裝置項目中，包含彎頭三通變徑管天圓地方等管件及法蘭加固框和吊托支架的制造用工但不包含過跨風管落地支架，落地支架履行設備支架項目。煙道過于狹窄，大排量煙機一般每分鐘排風量會在13立方米左右，過于狹小的煙道會造成排風受阻，氣流回轉，風壓加大產生的噪音，還有就是要檢查一下看看排煙管是否深入煙道過多，在墻壁或天花板上砌上消音磚，或涂上消音漆以及安裝隔音門等。

In the manufacturing equipment project of thin steel plate ventilation ducts, it includes the manufacturing labor for pipe fittings such as elbows, tees, and variable diameter pipes, as well as flange reinforcement frames and suspension brackets. However, it does not include the cross span air duct floor bracket, which fulfills the equipment support project. The flue is too narrow, and the exhaust air volume of a large displacement fan is generally around 13 cubic meters per minute. A narrow flue can cause obstruction of the exhaust air, rotation of the airflow, and noise generated by increased air pressure. Additionally, it is necessary to check whether the exhaust pipe penetrates too deeply into the flue, lay soundproof bricks on the wall or ceiling, apply soundproof paint, and install soundproof doors.

通風管道講解按用途區分其材質有哪些：

Explain which materials are used to distinguish ventilation ducts based on their purpose:

凈化空調系統用風管:鍍鋅板不繡鋼; (使用中可能出現塵源污染的玻璃鋼 復合材料禁用

Air ducts for purification air conditioning systems: galvanized sheet stainless steel; (Glass fiber reinforced plastic composite materials that may be contaminated by dust sources during use are prohibited)

空調系統用風管:鍍鋅板彩鋼保溫板; (可使用玻璃鋼復合材料

Air duct for central air conditioning system: galvanized sheet color steel insulation board; (Glass fiber reinforced plastic composite material can be used)

濟南通風管道的環境控制系統用風管:鍍鋅板不銹鋼; (可使用塑料玻璃鋼復合材料

Air ducts for the environmental control system of Jinan ventilation ducts: galvanized sheet stainless steel; Plastic fiberglass composite material can be used

工業通風系統用風管: 鋼板 鍍鋅板; (可使用塑料玻璃鋼復合材料

Air ducts for industrial ventilation systems: steel plate galvanized sheet; Plastic fiberglass composite material can be used

特殊使用場合用風管:礦用涂膠布風筒礦用塑料通風管; (要求阻燃抗靜電礦用特性

Air ducts for special occasions: mining coated cloth air ducts, mining plastic air ducts; (Requirements for flame-retardant and anti-static mining safety characteristics)