免费观看女子推理社,韩国女主播一区二区,美女让我桶,欧美一级黄色片视频

當前位置:首頁-新聞中心新聞中心

螺旋風管其長度等方面是要好于矩形風管

發布人:http://www.bnlfans.net   發布時間:2022-11-17 19:52:03

螺旋風管其長度等方面是要好于矩形風管:這是由于普通的螺旋風管,其正常長度是為3米到6米,而矩形風管其是為1米到1.5米,除此之外,螺旋風管的長度,還能夠依照具體需求來定做,從其它方面來看,螺旋風管中的連接點,是能夠很大程度上根絕的,由于其風管之間的連接,只用管接件,而矩形風管則需求雙法蘭體系。

The length of spiral air duct is better than that of rectangular air duct: this is because the normal length of ordinary spiral air duct is 3 to 6 meters, while that of rectangular air duct is 1 to 1.5 meters. In addition, the length of spiral air duct can also be customized according to specific needs. From other aspects, the connection points in spiral air duct can be eliminated to a large extent. Because the connection between air ducts only uses pipe connectors, The rectangular air duct requires double flange system.

1、通風管道加工的過程中應該盡量避免出現縱向接縫,但是一定不能出現橫向接縫。而且通風管道的咬口縫和四角的縫隙處,需要按照設計潔凈等級要求,然后還要采用密封膠將其堵嚴。另外通風管道板材的連接縫的密封面應該設在通風管道壁的正壓側。

1. The longitudinal joint shall be avoided as far as possible during the processing of the ventilation pipe, but the transverse joint shall not be allowed. Moreover, the seaming seams and the four corners of the ventilation pipe shall be sealed with sealant according to the design cleanliness level requirements. In addition, the sealing surface of the joint of the ventilation duct plate should be set at the positive pressure side of the ventilation duct wall.

鍍鋅螺旋風管

Galvanized spiral air duct

2、加工的時候,不能在通風管道內部設置加固框或者加固筋,因為這樣對于通風管道的質量會造成一定的影響。

2. During processing, reinforcing frames or reinforcements cannot be set inside the ventilation ducts, because this will have a certain impact on the quality of the ventilation ducts.

11.8使用.jpg

3、通風管道加工不能采用S型插條和C型直角插條的連接方式,另外對于一些特殊的通風管道來說,還不能采用按扣式的咬口。

3. The connection mode of S-shaped and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. In addition, snap joint cannot be used for some special ventilation ducts.

4、通風管道制作完畢之后,還要用清洗液進行清洗,只有達到清洗標準之后,才可以及時封口。

4. After the fabrication of the ventilation pipe, it shall be cleaned with cleaning solution. Only when the cleaning standard is met, can it be sealed in time.

5、玻璃纖維復合板風管端口為切割面時,在裝配法蘭連接件前應將管端切口面用膠帶或膠液進行封堵,才能防止玻璃纖維外露和飛散

5. When the end of the fiberglass composite board air duct is the cutting surface, the cut surface of the duct end should be sealed with tape or glue before assembling the flange connector to prevent the fiberglass from being exposed and flying

以上就是為大家介紹的有關濟南風管加工廠的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.bnlfans.net

The above is a detailed introduction to Jinan Air Duct Processing Factory, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.bnlfans.net


上一篇:通風管道加工系統布局要減小阻力
下一篇:鍍鋅螺旋風管對于散裝物料的輸送是怎樣的

網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

主站蜘蛛池模板: 日本久久久久亚洲中字幕| 成品大香煮伊在2021一| 国产精品9999久久久久仙踪林| 欧美人与动性xxxxx杂性| 日日日操| 丝袜足液精子免费视频| 最近高清中文字幕在线国语5 | 污污的小说片段| 精品国产福利久久久| 日韩精品武藤兰视频在线| 抱着cao才爽| 亚洲欧美精品一中文字幕| 波多野结衣与黑人| 欧美另类bbbxxxxx另类| 大佬的365天第三季完整视频在线观看 | 一本到在线观看视频| 久久成人免费播放网站| 樱桃视频高清免费观看在线播放| 久久www免费人成看片入口| 日b片| 日韩黄色一级| 嗯啊用力视频| 三上悠亚电影在线观看| 深夜影院一级毛片| 波多野结衣gvg708| 538在线观看| 女人爽小雪又嫩又紧| 又粗又大又爽又长又紧又水| 乱人伦中文视频在线观看免费| 精品久久久久久久久中文字幕| 欧美日韩亚洲电影| 国产激情久久久久影院小草| 免费大片黄国产在线观看| 嫩草影院免费观看| 免费a级毛片| 在线观看国产一区二区三区 | 波多野结衣护士系列播放| 毛片1| 性一交一乱一伦一色一情| 娃娃脸中文字幕1080p| 杨晨晨白丝mm131|