通風管道加固的規定要求有哪些？

發布人：http://www.bnlfans.net   發布時間：2022-04-27 21:06:00

通風管道的加固，關于風管來講也是非常重要的，并且對我們來講，也是要掌握的一個方面，由于它是有一些規定要求的，假如不恪守的話，那么不能達到良好的加固作用。并且，這也是一次學習新知識的好機會，可以讓我們愈加了解風管這一產品。

The reinforcement of ventilation duct is also very important for air duct, and it is also an aspect to be mastered for us. Because it has some regulations and requirements, if it is not strictly observed, it can not achieve good reinforcement. Moreover, this is also a good opportunity to learn new knowledge, which can let us know more about the product of air duct.

風管加固的規定要求，一般來講主要有以下這些，為：

Generally speaking, the specified requirements for air duct reinforcement mainly include the following:

(1)法蘭風管上如有加強筋的話，那么其凸出部分應在風管的表面面上，且擺放距離應均勻，板面不能出現變形。

(1) If there are stiffeners on the flange air duct, the protruding part shall be on the surface of the air duct, and the placement distance shall be uniform, and the plate surface shall not be deformed.

(2)假如風管的法蘭強度低于規定強度的話，那么可以進行加固處理，不過加固件與風管銜接法蘭一端之間的距離不能大于250毫米。

(2) If the flange strength of the air duct is lower than the specified strength, reinforcement can be carried out, but the distance between the reinforcement and one end of the connecting flange of the air duct shall not be greater than 250mm.

(3)外加固型材的高度，應不高于風管法蘭的高度，與風管應牢固銜接，螺栓或鉚接點之間的距離應不大于220毫米。

(3) The height of the external fixed profile shall not be higher than the height of the air duct flange, shall be firmly connected with the air duct, and the distance between bolts or riveting points shall not be greater than 220mm.

(4)假如風管內支撐加固的話，那么應擺放整齊，距離要均勻?qū)ΨQ，在支撐件兩頭的風管受力面處設置專用的墊圈。

(4) If the support in the air duct is reinforced, it should be placed neatly, the distance should be uniform and symmetrical, and special gaskets should be set at the stress surface of the air duct at both ends of the support.

(5)風管的密封，應運用板材銜接這一方法，不過也可以選用密封膠嵌縫，或者是其它一些密封方法。假如運用密封膠，那么應符合規定要求，密封面應設在風管的正壓面。

(5) For the sealing of air duct, the method of plate connection should be used, but sealant caulking or other sealing methods can also be used. If sealant is used, it shall meet the specified requirements, and the sealing surface shall be set on the positive pressure surface of the air duct.

(6)角鋼、加固筋與風管進行鉚接時，應是牢固的，相接處應連成一體。

(6) When riveting the angle steel and reinforcement with the air duct, it shall be firm and the joint shall be connected as a whole.

(7)法蘭在安裝到風管上之前，應做好漆，避免污染風管。

(7) Before the flange is installed on the air duct, it shall be painted to avoid polluting the air duct.

以上就是為大家介紹的有關濟南鐵皮風管加工濟南鐵皮風管加工的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.jntfgd.com

The above is a detailed introduction to the processing of Jinan iron sheet air duct. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.jntfgd.com