通風管道各個部分安裝規范標準你清楚嗎?

發布人：http://www.bnlfans.net   發布時間：2020-06-15 19:13:16

　　通風管道各個部分安裝規范標準你清楚嗎?今天小編來給大家詳細介紹一下通風管道各個部分安裝規范標準。

　　Do you know the installation specifications and standards of each part of the ventilation duct? Today, I will introduce the installation specifications and standards of each part of the ventilation duct in detail.

　　一，風管安裝規范標準

　　1、 Code and standard for air duct installation

　　1.風管內嚴禁其他管線穿越；

　　1. It is forbidden to cross other pipelines in the air duct;

　　2.輸送含有易燃、易爆氣體或安裝在易燃、易爆環境的風管系統應有良好的接地，通過生活區或其他輔助生產房間時必須嚴密，并不得設置接口

　　2. The air duct system for conveying inflammable and explosive gas or installed in inflammable and explosive environment shall be well grounded. It must be tight when passing through the living area or other auxiliary production rooms, and no interface shall be set

　　3.輸送空氣溫度高于80℃的風管，應按設計規定采取防護措施。

　　3. Protective measures shall be taken for air pipes with air temperature higher than 80 ℃ according to design regulations.

　　4.室外立管的固定拉索嚴禁拉在避雷針或避雷網上

　　4. The fixed cable of outdoor riser shall not be pulled on the lightning rod or lightning protection net

　　二，風管部件安裝必須符合下列規定：

　　2、 The installation of air duct components must meet the following requirements:

　　1.各類風管部件及操作機構的安裝，應能保證其正常的使用功能，并便于操作；

　　1. The installation of various air duct components and operating mechanisms shall ensure their normal use function and be easy to operate;

　　2.斜插板風閥的安裝，閥板必須為向上拉啟；水平安裝時，閥板還應為順氣流方向插入；

　　2. For the installation of inclined plug plate air valve, the valve plate must be pulled upward; for horizontal installation, the valve plate shall also be inserted along the air flow direction;

　　3.止回風閥、自動排氣活門的安裝方向應正確。

　　3. The installation direction of check air valve and automatic exhaust valve shall be correct.

　　4.防火閥、排煙閥（口）的安裝方向、位置應正確。防火分區隔墻兩側的防火閥，距墻表面不應大于200mm。

　　4. The installation direction and position of fire damper and smoke exhaust valve (port) shall be correct. The distance between the fire damper on both sides of the partition wall of the fire compartment and the wall surface shall not be more than 200mm.

　　5.手動密閉閥安裝，閥門上標志的箭頭方向必須與受沖擊波方向一致。

　　5. For the installation of manual airtight valve, the arrow direction marked on the valve must be consistent with the direction of shock wave.

　　6.風管系統安裝完畢后，應按系統類別進行嚴密性檢驗，漏風量應符合設計與風管必須通過工藝性的檢測或驗證，其強度和嚴密性要求應符合設計或下列規定：

　　6. After the installation of the air duct system, the tightness inspection shall be carried out according to the system category. The air leakage shall meet the design and the air duct must pass the technical inspection or verification, and the strength and tightness requirements shall meet the design or the following requirements:

　　① 風管的強度應能滿足在1.5倍工作壓力下接縫處無開裂；

　　① The strength of air duct shall be able to meet the requirement that there is no crack at the joint under 1.5 times of working pressure;

　　② 矩形風管的允許漏風量應符合以下規定：

　　② The allowable air leakage of rectangular air duct shall meet the following requirements:

　　低壓系統風管 QL≤0.1056P0.65

　　Low pressure system air duct QL ≤ 0.1056p0.65

　　中壓系統風管 QM≤0.0352P0.65

　　Medium pressure system air duct QM ≤ 0.0352p0.65

　　高壓系統風管 QH≤0.0117 P0.65

　　High pressure system air duct QH ≤ 0.0117 p0.65

　　式中 QL、QM、QH——系統風管在相應工作壓力下，單位面積風管單位時間內的允許漏風量[m3/(h·m2)]；

　　Where QL, QM, QH -- allowable air leakage of system air duct in unit time per unit area of air duct under corresponding working pressure [m3 / (H · m2)];

　　P——指風管系統的工作壓力（Pa）。

　　P -- working pressure of air duct system (PA).

　　③ 低壓、中壓圓形金屬風管、復合材料風管以及采用非法蘭形式的非金屬風管的允許漏風量，應為矩形風管規定值的50%；

　　③ The allowable air leakage of low and medium pressure circular metal air ducts, composite air ducts and non-metal air ducts in non flange form shall be 50% of the specified value of rectangular air ducts;

　　④ 磚、混凝土風道的允許漏風量不應大于矩形低壓系統風管規定值的1.5倍；

　　④ The allowable air leakage of brick and concrete air duct shall not be greater than 1.5 times of the specified value of rectangular low-pressure system air duct;

　　⑤ 排煙、除塵、低溫送風系統按中壓系統風管的規定，1~5級凈化空調系統按高壓系統風管的規定。

　　⑤ The smoke exhaust, dust removal and low temperature air supply system shall be in accordance with the provisions of the medium pressure system air duct, and the level 1-5 purification air conditioning system shall be in accordance with the provisions of the high pressure system air duct.