通風管道加工需要注意哪些事項？

發布人：http://www.bnlfans.net   發布時間：2018-04-17 20:26:48

濟南順發通風管道工程是一家致力于為廣大消費者提供濟南通風管道，空調風管、消防排煙風管、鍍鋅風管等產品的機構。公司不僅產品種類齊全，配套性強，適應面寬，而且可以為用戶提供完整的技術支持及工程解決方案。同時公司擁有一支強大的生產研發隊伍，以滿足不同客戶需求并確保公司的技術及產品始終保持行業地位。

Ji'nan Shun Fa ventilation pipeline project is a professional organization dedicated to providing high quality Ji'nan ventilation pipe, air conditioning wind pipe, fire exhaust pipe, galvanized wind pipe and other products for the majority of consumers. The company not only has a complete range of products, strong matching, wide adaptability, but also can provide users with complete technical support and engineering solutions. At the same time, the company has a strong R & D team to meet different customer needs and ensure that the technology and products of the company always maintain the leading position in the industry. 

在建筑業快速發展的現在，高層建筑越來越多，為了保護在內工作人員的身體健康，通風管道的運用也多了起來，在給通風管道加工時，有很多事項要注意，下面主要是一些常見的問題：

In the rapid development of the construction industry now, more and more high-rise buildings, in order to protect the health of the staff, the use of ventilation pipes is also more, in the processing of ventilation pipes, there are many issues to pay attention to, the following are a number of common problems:

通風管道加工的過程中應該盡量避免出現縱向接縫，但是不能出現橫向接縫，而且通風管道的咬口縫和四角的縫隙處，需要按照設計潔凈等級要求，然后還要采用密封膠將其堵嚴。另外通風管道板材的連接縫的密封面應該設在通風管道壁的正壓側，通風管道加工不能采用S型插條和C型直角插條的連接方式，另外對于一些特殊的通風管道來說，還不能采用按扣式的咬口，如果是彩色涂層鋼板通風管道的話，應該保持內壁是光滑的，而且通風管道加工的過程中，還不能將涂層損壞，若是出現損壞的部位，需要用環氧樹脂涂刷在表面即可。

The longitudinal joint should be avoided in the process of the ventilation pipe processing, but the transverse joint must not appear, and the slot seam of the ventilation pipe and the gap in the four corner should be designed according to the requirements of the design cleanliness, and then the sealant will be used to block it. In addition, the sealing surface of the joint joint of the ventilation pipe plate should be located on the positive pressure side of the ventilation pipe wall. The ventilation pipe can not be processed by the connection mode of the S bar and the C right angle bar. In addition, for some special ventilation pipes, the button type bite is not used, if the fruit is a color coated steel plate ventilation pipe. The inner wall should be kept smooth and the coating can not be damaged during the processing of the ventilation pipe. If the damaged parts appear, the epoxy resin should be painted on the surface.

另外通風管道加工的過程中，還要做好防腐蝕措施，不能使用抽芯鉚釘，而且在通風管道零件裝配的時候，這些零件都要經過鍍鋅處理才行，加工的時候，不能在通風管道內部設置加固框或者加固筋，因為這樣對于通風管道的質量會造成一定的影響，通風管道制作完畢之后，還要用清洗液進行清洗，只有達到清洗標準之后，才可以及時封口，如果做到以上問題不出錯的話，在給通風管道加工時應該沒有多大問題。

In addition, in the process of the ventilation pipe processing, we should do a good job of anti-corrosion measures, can not use the core rivet, and when the parts of the ventilation pipe are assembled, these parts must be galvanized. When processing, the reinforcement frame or reinforcement can not be set in the ventilation pipe, because this is the case for the ventilation pipe. Quality will cause a certain impact, after the production of the ventilation pipe, but also use the cleaning liquid cleaning, only after the cleaning standard, can be timely sealed, if the above problems do not make mistakes, in the ventilation pipe processing should not have many problems.

想了解更多關于濟南通風管道知識請關注濟南順發通風管道工程 http://www.bnlfans.net/ 歡迎來電詳細咨詢。

For more information on ventilation pipe in Ji'nan, please pay attention to Ji'nan Shun Fa ventilation pipe project http://www.bnlfans.net/. Welcome to call for detailed consultation.